A leading specialist in capturing, processing and distributing TV signals

When you install an ALCAD solution, you are installing European-made products with an assurance of quality and reliability. Thanks to this, more than 20 million people in more than 60 countries on 5 continents benefit from our solutions and already watch television with ALCAD products, making us a worldwide benchmark.

Our catalogue offers top-of-the-line products, such as himalaya modular headends, Mont Blanc programmable amplifier, Everest multiband amplifiers or our powerful range of antennas.

CATALOGUE_ALCAD_EN_MULTIMEDIA_TV pdf 7.33 MB

Get to know it in depth

  • RECEPTION AND CAPTURE OF TELEVISION SIGNALS

    RECEPTION AND CAPTURE OF TELEVISION SIGNALS

  • SIGNAL PROCESSING

    SIGNAL PROCESSING

    • Amplifiers, mixers and mast filters

      ALCAD has a wide range of broadband amplifiers for masts, compatible with emission of LTE mobile telephony signals with an amplification band within UHF 470 - 790 MHz. There are also a great variety of mixers and filters for masts that allow the signals from several antennas to be mixed via a single coaxial cable.

      Some of the amplifiers include an LTE rejection filter. They have one, two, three, four or five configurable inputs, to amplify and combine the signals from the antennas.  They are fed through the coaxial cable from a feeder installed inside the building. They incorporate switchable current steps to accept the power of a pre-amplifier.

      Typical applications

      Digital and analogue terrestrial TV installations of an individual type that may or may not be affected by the emission of LTE mobile telephony signals with low or high gain requirements. Amplifies and mixes signals arriving from various antennas. The signal obtained can be distributed to a large number of TV sockets through a single coaxial cable.

      INSTALLATION EXAMPLES:

      Individual installations with mast amplifier or mixer

      The mixer allows installation when signal reception levels are high. If the levels are not high or the installation has several TV outlets it will be necessary to use an amplifier and a feeder.

      Individual installations with mast amplifier

      Installation with a UHF antenna and with an antenna pre-amplifier; the antenna pre-amplifier is used when the signal level is very low. To activate the power supply of the pre-amplifier, turn the current step switch ON. There are two sockets connected to the outputs of the feeder and a third socket connected to the -15 dB output of the amplifier.

      Installation with two antennas, UHF and BIII, and a pre-amplifier for the UHF antenna. The antenna pre-amplifier is used when the signal level is very low. To activate the power supply of the pre-amplifier, turn the current step switch ON. There are two sockets connected to the outputs of the feeder and a third socket connected to the -15 dB output of the amplifier.

      Installation with two antennas, UHF and BIII, and two pre-amplifiers for the UHF antenna. The signal levels of each antenna are adjusted with the gain controllers so that the output level of all channels is similar.

      Installation with four antennas, two UHF, one BIII and one FM. One of the UHF antennas has a pre-amplifier. The signal levels of each antenna are adjusted with the gain controllers so that the output level of all channels is similar.

      Find out more under the Multimedia-TV Products section.

    • Multi-band amplifiers

      Compact multi-band amplifiers for mastheads of MATV and individual TV installations. Used together with an equaliser filter, they allow quality reception in adverse conditions.

      ALCAD, as a global leader in amplification, has a wide range of multi-band amplifiers with output levels ranging from 110 dBuV up to 122 dBuV.

       

      EVEREST, the range of multi-band amplifiers inspired by the Top of the World

      The EVEREST range stands out as the star of the family, with its 117 dBuV output level, a robust all-metal design and multiple advantages that elevate it to the top of the world in amplification.

      WIDE and COMPLETE range. All Everest multiband amplifiers have 117 dBμV output level.

      • RELIABLE AND VERSATILE. Redundant power supply thanks to the integrated power supply and the option to connect an external one. This feature reduces dramatically the risk of failure. Moreover, switchable gain makes it adaptable to any kind of installation.
      • ROBUST. There are no plastic elements on the Everest range by offering a 100% metallic chassis and prepared for harsh environment.
      • EASY and QUICK installation and commissioning. No need to use a programmer or any special tools.
      • COMPACT DESIGN. This range is the smallest we have ever created; it will fit into any gap in the installation with its 156x139x36 millimeters.
      • Made in Spain and CE certificate

      Find out more under the Multimedia-TV Products section.

       

      Beyond EVEREST

      ALCAD's multiband amplifier range comprises a wide variety of models with an ABS and / or zamak chassis, with maximum shielding guaranteed for both terrestrial and SAT TV. There are also filters, equalisers and accessories.

              

      Find out more under the Multimedia-TV Products section.

       

      Installation examples:

      HEADMAST AMPLIFIER WITH EQUALISER FILTER

      Headmast device for terrestrial TV comprising an equaliser filter and a broadband amplifier. Adjusting the attenuators of the equaliser filter equalises the levels of all the channels before amplification, meaning that the intermodulation in the broadband amplifier is reduced and a higher output level is obtained.

      Headmast device for terrestrial TV comprising an equaliser filter and a broadband amplifier. Adjusting the attenuators of the equaliser filter equalises the levels of all the channels before amplifying, meaning that the intermodulation in the broadband amplifier is reduced and a higher output level is obtained. The amplifier automatically feeds UHF antenna pre-amplifiers.

      INDIVIDUAL INSTALLATIONS WITH HEADMAST AMPLIFIER

      Individual terrestrial TV installation with amplifier and power amplifier mast used as a pre-amplifier. The pre-amplifier is fed from the amplifier. This configuration is suitable when the signal levels received are very weak.

      HEADMAST AMPLIFIER WITH STAR DISTRIBUTION

      MATV terrestrial TV installation with headmast broadband amplifier. The gain of each amplifier input allows you to adjust the levels of each of the antennas. The distribution takes place in a star pattern using the two amplifier outputs and distributors. This type of distribution allows the maximum number of outlets at the expense of using more coaxial cable.

      HEADMAST AMPLIFIER WITH TREE DISTRIBUTION

      MATV terrestrial TV installation with headmast broadband amplifier. The gain of each amplifier input allows you to adjust the levels of each of the antennas. The distribution takes place in a tree pattern using splitters. This type of distribution allows the signal levels to be balanced across all installations.

      INDIVIDUAL INSTALLATIONS WITH TV-SAT HEADMAST AMPLIFIER

      Individual terrestrial TV or satellite installation. The head amplifier is connected to a UHF antenna or an individual parabola, where signals are being received from several terrestrial TV antennas a mast mixer will be used. The LNB is powered and controlled from the individual receiver, through the amplifier.

      Find out more under the Multimedia-TV Products section.

    • Splitband and extension amplifiers

      ALCAD offers a professional, market-leading range of extension amplifiers for long coaxial and splitband cable lines to increase the number of outlets in a residence. This range covers all terrestrial and satellite TV bands. 

    • Modular amplification and TDT processing equipment (LTE compatible)

      Modular amplification equipment, channel processors or transmodulators for large MATV TV installations.

      Channel converter equipment to organise the spectrum as needed.

      905-ZA: Modular and programmable amplification device

      DESCRIPTION
      Programmable amplification device for analogue and digital terrestrial TV, and for analogue FM and digital DAB radio. This is a modular system that consists of a feeder, a broadband amplifier, filters and channel processors that are mounted on a support frame. It enables the processing of any combination of channels, including adjacent channels with multi-channel or single-channel processing. All functions are programmable via a programmer. Simple assembly, easily adaptable to each situation thanks to the input demixing and output mixing system.

      APPLICATIONS
      Medium-size MATV digital and analogue terrestrial TV installations. Areas where there are several broadcasters and it is not possible to predict the receivable channels. A recommended device for installations where more professional equipment is necessary than traditional compact devices.

      CHARACTERISTICS
      The device is characterised by its modularity and versatility. It allows you to install the necessary number of channels, and add further amplification without channel limits. Fully configurable in terms of number of inputs and channels in each input. Zamak chassis with metal caps. Female connector. Power connection via ribbon cable with 10-pin polarised connectors. Simple, fast device assembly. The main advantage of this device is the automatic and fast programming and adjustment of all the device filters.

      Find out more under the Multimedia-TV Products section.

       

      905-ZG: Modular amplification device

      DESCRIPTION
      Modular amplification device for analogue and digital terrestrial TV, and for analogue FM and digital DAB radio. It consists of a feeder and amplification modules that are mounted on a support frame.
      It enables the processing of any combination of channels, including adjacent channels with single-channel or multi-channel processing. Simple assembly, easily adaptable to each situation thanks to the input demixing and output mixing system.

      APPLICATIONS
      Large MATV digital and analogue terrestrial TV installations. Areas where reception is difficult, with large differences in level between channels. Recommended device for installations in hotels, hospitals and other large buildings with a large number of channels.

      CHARACTERISTICS
      The device is characterised by its low consumption, making it highly reliable. Zamak chassis with metal caps. High-quality machined female connectors. Power connection via ribbon cable with 10-pin polarised connectors. Simple, fast device assembly. The main advantage of this device is the quick equalisation and adjustment of all installation channels under any reception conditions, however adverse. Device is compatible with the old 905-ZG series.

      Find out more under the Multimedia-TV Products section.

       

      905-TO: Transmodulators

      DESCRIPTION
      Modular COFDM-PAL transmodulator device for digital terrestrial TV channels.
      The device converts digital terrestrial DVB-T channels into analogue TV channels in the terrestrial band. It consists of a feeder, an amplifier and up to 6 transmodulators that are mounted on a support frame. All functions are programmable via a programmer. The various modules are compatible with the B / G, D / K and I standards.

      APPLICATIONS
      MATV digital terrestrial TV installations, where users do not have individual digital terrestrial receivers. Areas where analogue channel reception is difficult, with large differences in level between channels and for adjacent channels. Compatible with all MATV TV installations because the channels are distributed via the terrestrial band.
      Recommended device for installations in hotels, hospitals and other large buildings.
      It is not necessary to install individual DVB-T digital terrestrial TV receivers with each television.

      CHARACTERISTICS
      Reintegration of teletext, support and inversion of dual audio, subtitle support and programmable 4:3 or 16:9 image formats. The device is characterised by its wide operating temperature tolerance, making it highly reliable. Chassis in zamak with metallic side covers. Female connectors. Simple, fast device assembly.

      Find out more under the Multimedia-TV Products section.

       

      905-PC: Channel processing equipment

      DESCRIPTION
      Modular channel processor device for digital and analogue terrestrial TV. The device filters channels with a high degree of selectivity, regulating the channel levels and converting the frequency if necessary. It consists of a feeder and processing modules that are mounted on a support frame. It enables the processing of any combination of channels, including adjacent channels with significant level differences. All functions are programmable through a programmer, including the selection of input and output channels.

      APPLICATIONS
      MATV digital and analogue terrestrial TV installations in areas where reception is difficult, with significant differences in level between adjacent channels. The automatic control of CAG gain allows installations to be set up in areas with variable reception levels. Installations where it is necessary to convert the frequency of the digital channels.

      CHARACTERISTICS
      Zamak chassis with metal caps. Female connector, Power connection via ribbon cable with 20-pin polarised connectors. Simple, fast device assembly. Filtering and frequency conversion using double conversion with FOS surface wave filter. The main advantages of this device is its selectivity, which prevents interference between channels and frequency conversions without incompatibilities.

      Find out more under the Multimedia-TV Products section.

       

      905-RG: Signal regenerator equipment

      DESCRIPTION
      Programmable device for regeneration of digital channels modulated in DVB-T for BIII and UHF bands. The device regenerates DVB-T digital channels, reconstructing all channels across the VHF-UHF band and obtaining optimal signal quality.

      This modular system consists of a feeder, an amplifier and up to 10 transmodulators that are mounted on a support frame. All functions are programmable via PC software and/or a wireless programmer.

      APPLICATIONS
      MATV installations of digital terrestrial TV and signal transmission or re-transmission installations, where a complete DVB-T channel needs to be regenerated. Areas where the reception of digital channels is difficult due to orographic conditions, or where you wish to improve the quality of the channel considerably. Compatible with all MATV TV installations because the channels are distributed across the entire terrestrial band, BI, BIII, BS and UHF.

      CHARACTERISTICS
      The main characteristic of this device is the high quality of the regenerated output channel and its simplicity of use. Adjustable frequency for input channels in 250 KHz steps. The high selectivity prevents interference between channels and allows frequency conversion without incompatibilities. Chassis in zamak with metallic side covers.
      Female connectors. Simple, fast device assembly.

      Find out more under the Multimedia-TV Products section.

       

      905-ZP: amplification equipment

      DESCRIPTION
      Modular amplification device for analogue and digital terrestrial TV, and for analogue FM and digital DAB radio. It consists of a feeder and amplification modules that are mounted on a support frame.
      It enables the processing of any combination of channels, including adjacent channels with single-channel or multi-channel processing. Simple assembly, easily adaptable to each situation thanks to the input demixing and output mixing system.

      APPLICATIONS
      Medium-to-large MATV digital and analogue terrestrial TV installations. Areas where reception is difficult, with large differences in level between channels.
      Recommended device for installations in residential buildings with a large number of channels.

      CHARACTERISTICS
      The device is characterised by its low consumption, making it highly reliable. Zamak chassis with metal caps. High-quality machined female connectors. Power connection via ribbon cable with 10-pin polarised connectors. Simple, fast device assembly. The main advantage of this device is the quick equalisation and adjustment of all installation channels under any reception conditions, however adverse. Device compatible with the old 905-ZP series.

      Find out more under the Multimedia-TV Products section.

       

      INSTALLATION EXAMPLES:

      DEVICE WITH PROGRAMMABLE AMPLIFIERS

      Complete 905-ZA device where the assembly and module operation methods are indicated. Each ZA-411 module can be programmed for single-channel or multi-channel operation, amplifying several channels, the ZA-431 can be programmed to act as high-selectivity filters for adjacent UHF channels. The ZA-331 can be programmed to act as high-selectivity filters for adjacent VHF channels.

      DEVICE WITH PROGRAMMABLE SINGLE-CHANNEL AMPLIFIERS

      Complete 905-ZG or 905-ZP device where the module assembly methods are indicated. It is recommended to connect the modules with the mixing and demixing bridges as indicated in the drawing. When using the demixing bridges (on top of the device), it is necessary to replace the metal caps for 75ohm loads.

      DEVICE WITH PROGRAMMABLE SINGLE-CHANNEL AMPLIFIERS

      Complete 905-ZG or 905-ZP device where the module assembly methods are indicated. It is recommended to connect the modules with the mixing and demixing bridges as indicated in the drawing. When using the demixing bridges (on top of the device), it is necessary to replace the metal caps for 75ohm loads.

      Find out more under the Multimedia-TV Products section.

    • TV-SAT modulators and equipment

      Modulator devices that generate TV channels and complete MATV TV installations in large buildings and hotels with video surveillance cameras and video or DVD machines.

      912-DM: Digital modulator equipment 

      DESCRIPTION
      Modular TV modulator device, which generates a digital TV channel in DVB-T or DVB-C from two audio and video signals. It is a modular system that consists of a feeder, an amplifier and modulators, which are mounted on a support frame. All functions are programmable via PC software and/or a wireless programmer. Multi-standard device.

      APPLICATIONS
      MATV terrestrial or digital cable TV installations where it is necessary to incorporate channels generated locally from SAT receivers, DVDs, videos or surveillance cameras.

      CHARACTERISTICS
      The main characteristic of this device is the high quality of the regenerated output channel and its simplicity of use. Chassis in zamak with metallic side covers. Female connectors. Simple, fast device assembly.

      Find out more under the Multimedia-TV Products section.

       

      912-TT/TQ/TP: Digital satellite equipment

      DESCRIPTION
      Modular transmodulator devices that, based on satellite digital television signals, generate a terrestrial (TT models) or cable (TQ models) or PAL (TP models) digital TV channel. The device converts digital satellite television services into DVB-S / S2 for programmes included in a digital terrestrial TV channel with DVB-T (TT models) modulation, or in DVB-C (TQ models), or PAL (TP models).

      It consists of a feeder, an amplifier and up to 8 transmodulators, depending on the model. All functions are programmable via PC software and/or a wireless programmer. 

      APPLICATIONS
      MATV digital terrestrial television installations where it is necessary to generate a complete DVB-T or DVB-C channel containing services from digital satellite signals with DVB-S/S2 modulation, both free and encrypted. It is not necessary to install individual satellite receivers. Compatible with all MATV TV installations since the channels can be distributed over the entire terrestrial (TT models) or MATV band by cable, since the channels can be distributed throughout the 47-862 MHz band. Compatible with remote control systems.

      CHARACTERISTICS
      Allows the insertion of NIT tables. Programming of the output channel by frequency or by means of a channel table, generating a channel of particularly good quality. Chassis in zamak with metallic side covers. Female connectors. Simple, fast device assembly.

      Find out more under the Multimedia-TV Products section.

    • Digital and analogue home automation modulators
    • IPTV modular headend

      Also known as streamers, these are modular products mounted on a 19” rack, accepting signals from DVB-T / T2, DVB-S / S2, A / V, and HDMI.

      Find more information in the MM-TV Products section.

    ALCAD has a wide range of broadband amplifiers for masts, compatible with emission of LTE mobile telephony signals with an amplification band within UHF 470 - 790 MHz. There are also a great variety of mixers and filters for masts that allow the signals from several antennas to be mixed via a single coaxial cable.

    Some of the amplifiers include an LTE rejection filter. They have one, two, three, four or five configurable inputs, to amplify and combine the signals from the antennas.  They are fed through the coaxial cable from a feeder installed inside the building. They incorporate switchable current steps to accept the power of a pre-amplifier.

    Typical applications

    Digital and analogue terrestrial TV installations of an individual type that may or may not be affected by the emission of LTE mobile telephony signals with low or high gain requirements. Amplifies and mixes signals arriving from various antennas. The signal obtained can be distributed to a large number of TV sockets through a single coaxial cable.

    INSTALLATION EXAMPLES:

    Individual installations with mast amplifier or mixer

    The mixer allows installation when signal reception levels are high. If the levels are not high or the installation has several TV outlets it will be necessary to use an amplifier and a feeder.

    Individual installations with mast amplifier

    Installation with a UHF antenna and with an antenna pre-amplifier; the antenna pre-amplifier is used when the signal level is very low. To activate the power supply of the pre-amplifier, turn the current step switch ON. There are two sockets connected to the outputs of the feeder and a third socket connected to the -15 dB output of the amplifier.

    Installation with two antennas, UHF and BIII, and a pre-amplifier for the UHF antenna. The antenna pre-amplifier is used when the signal level is very low. To activate the power supply of the pre-amplifier, turn the current step switch ON. There are two sockets connected to the outputs of the feeder and a third socket connected to the -15 dB output of the amplifier.

    Installation with two antennas, UHF and BIII, and two pre-amplifiers for the UHF antenna. The signal levels of each antenna are adjusted with the gain controllers so that the output level of all channels is similar.

    Installation with four antennas, two UHF, one BIII and one FM. One of the UHF antennas has a pre-amplifier. The signal levels of each antenna are adjusted with the gain controllers so that the output level of all channels is similar.

    Find out more under the Multimedia-TV Products section.

    Compact multi-band amplifiers for mastheads of MATV and individual TV installations. Used together with an equaliser filter, they allow quality reception in adverse conditions.

    ALCAD, as a global leader in amplification, has a wide range of multi-band amplifiers with output levels ranging from 110 dBuV up to 122 dBuV.

     

    EVEREST, the range of multi-band amplifiers inspired by the Top of the World

    The EVEREST range stands out as the star of the family, with its 117 dBuV output level, a robust all-metal design and multiple advantages that elevate it to the top of the world in amplification.

    WIDE and COMPLETE range. All Everest multiband amplifiers have 117 dBμV output level.

    • RELIABLE AND VERSATILE. Redundant power supply thanks to the integrated power supply and the option to connect an external one. This feature reduces dramatically the risk of failure. Moreover, switchable gain makes it adaptable to any kind of installation.
    • ROBUST. There are no plastic elements on the Everest range by offering a 100% metallic chassis and prepared for harsh environment.
    • EASY and QUICK installation and commissioning. No need to use a programmer or any special tools.
    • COMPACT DESIGN. This range is the smallest we have ever created; it will fit into any gap in the installation with its 156x139x36 millimeters.
    • Made in Spain and CE certificate

    Find out more under the Multimedia-TV Products section.

     

    Beyond EVEREST

    ALCAD's multiband amplifier range comprises a wide variety of models with an ABS and / or zamak chassis, with maximum shielding guaranteed for both terrestrial and SAT TV. There are also filters, equalisers and accessories.

            

    Find out more under the Multimedia-TV Products section.

     

    Installation examples:

    HEADMAST AMPLIFIER WITH EQUALISER FILTER

    Headmast device for terrestrial TV comprising an equaliser filter and a broadband amplifier. Adjusting the attenuators of the equaliser filter equalises the levels of all the channels before amplification, meaning that the intermodulation in the broadband amplifier is reduced and a higher output level is obtained.

    Headmast device for terrestrial TV comprising an equaliser filter and a broadband amplifier. Adjusting the attenuators of the equaliser filter equalises the levels of all the channels before amplifying, meaning that the intermodulation in the broadband amplifier is reduced and a higher output level is obtained. The amplifier automatically feeds UHF antenna pre-amplifiers.

    INDIVIDUAL INSTALLATIONS WITH HEADMAST AMPLIFIER

    Individual terrestrial TV installation with amplifier and power amplifier mast used as a pre-amplifier. The pre-amplifier is fed from the amplifier. This configuration is suitable when the signal levels received are very weak.

    HEADMAST AMPLIFIER WITH STAR DISTRIBUTION

    MATV terrestrial TV installation with headmast broadband amplifier. The gain of each amplifier input allows you to adjust the levels of each of the antennas. The distribution takes place in a star pattern using the two amplifier outputs and distributors. This type of distribution allows the maximum number of outlets at the expense of using more coaxial cable.

    HEADMAST AMPLIFIER WITH TREE DISTRIBUTION

    MATV terrestrial TV installation with headmast broadband amplifier. The gain of each amplifier input allows you to adjust the levels of each of the antennas. The distribution takes place in a tree pattern using splitters. This type of distribution allows the signal levels to be balanced across all installations.

    INDIVIDUAL INSTALLATIONS WITH TV-SAT HEADMAST AMPLIFIER

    Individual terrestrial TV or satellite installation. The head amplifier is connected to a UHF antenna or an individual parabola, where signals are being received from several terrestrial TV antennas a mast mixer will be used. The LNB is powered and controlled from the individual receiver, through the amplifier.

    Find out more under the Multimedia-TV Products section.

    ALCAD offers a professional, market-leading range of extension amplifiers for long coaxial and splitband cable lines to increase the number of outlets in a residence. This range covers all terrestrial and satellite TV bands. 

    Modular amplification equipment, channel processors or transmodulators for large MATV TV installations.

    Channel converter equipment to organise the spectrum as needed.

    905-ZA: Modular and programmable amplification device

    DESCRIPTION
    Programmable amplification device for analogue and digital terrestrial TV, and for analogue FM and digital DAB radio. This is a modular system that consists of a feeder, a broadband amplifier, filters and channel processors that are mounted on a support frame. It enables the processing of any combination of channels, including adjacent channels with multi-channel or single-channel processing. All functions are programmable via a programmer. Simple assembly, easily adaptable to each situation thanks to the input demixing and output mixing system.

    APPLICATIONS
    Medium-size MATV digital and analogue terrestrial TV installations. Areas where there are several broadcasters and it is not possible to predict the receivable channels. A recommended device for installations where more professional equipment is necessary than traditional compact devices.

    CHARACTERISTICS
    The device is characterised by its modularity and versatility. It allows you to install the necessary number of channels, and add further amplification without channel limits. Fully configurable in terms of number of inputs and channels in each input. Zamak chassis with metal caps. Female connector. Power connection via ribbon cable with 10-pin polarised connectors. Simple, fast device assembly. The main advantage of this device is the automatic and fast programming and adjustment of all the device filters.

    Find out more under the Multimedia-TV Products section.

     

    905-ZG: Modular amplification device

    DESCRIPTION
    Modular amplification device for analogue and digital terrestrial TV, and for analogue FM and digital DAB radio. It consists of a feeder and amplification modules that are mounted on a support frame.
    It enables the processing of any combination of channels, including adjacent channels with single-channel or multi-channel processing. Simple assembly, easily adaptable to each situation thanks to the input demixing and output mixing system.

    APPLICATIONS
    Large MATV digital and analogue terrestrial TV installations. Areas where reception is difficult, with large differences in level between channels. Recommended device for installations in hotels, hospitals and other large buildings with a large number of channels.

    CHARACTERISTICS
    The device is characterised by its low consumption, making it highly reliable. Zamak chassis with metal caps. High-quality machined female connectors. Power connection via ribbon cable with 10-pin polarised connectors. Simple, fast device assembly. The main advantage of this device is the quick equalisation and adjustment of all installation channels under any reception conditions, however adverse. Device is compatible with the old 905-ZG series.

    Find out more under the Multimedia-TV Products section.

     

    905-TO: Transmodulators

    DESCRIPTION
    Modular COFDM-PAL transmodulator device for digital terrestrial TV channels.
    The device converts digital terrestrial DVB-T channels into analogue TV channels in the terrestrial band. It consists of a feeder, an amplifier and up to 6 transmodulators that are mounted on a support frame. All functions are programmable via a programmer. The various modules are compatible with the B / G, D / K and I standards.

    APPLICATIONS
    MATV digital terrestrial TV installations, where users do not have individual digital terrestrial receivers. Areas where analogue channel reception is difficult, with large differences in level between channels and for adjacent channels. Compatible with all MATV TV installations because the channels are distributed via the terrestrial band.
    Recommended device for installations in hotels, hospitals and other large buildings.
    It is not necessary to install individual DVB-T digital terrestrial TV receivers with each television.

    CHARACTERISTICS
    Reintegration of teletext, support and inversion of dual audio, subtitle support and programmable 4:3 or 16:9 image formats. The device is characterised by its wide operating temperature tolerance, making it highly reliable. Chassis in zamak with metallic side covers. Female connectors. Simple, fast device assembly.

    Find out more under the Multimedia-TV Products section.

     

    905-PC: Channel processing equipment

    DESCRIPTION
    Modular channel processor device for digital and analogue terrestrial TV. The device filters channels with a high degree of selectivity, regulating the channel levels and converting the frequency if necessary. It consists of a feeder and processing modules that are mounted on a support frame. It enables the processing of any combination of channels, including adjacent channels with significant level differences. All functions are programmable through a programmer, including the selection of input and output channels.

    APPLICATIONS
    MATV digital and analogue terrestrial TV installations in areas where reception is difficult, with significant differences in level between adjacent channels. The automatic control of CAG gain allows installations to be set up in areas with variable reception levels. Installations where it is necessary to convert the frequency of the digital channels.

    CHARACTERISTICS
    Zamak chassis with metal caps. Female connector, Power connection via ribbon cable with 20-pin polarised connectors. Simple, fast device assembly. Filtering and frequency conversion using double conversion with FOS surface wave filter. The main advantages of this device is its selectivity, which prevents interference between channels and frequency conversions without incompatibilities.

    Find out more under the Multimedia-TV Products section.

     

    905-RG: Signal regenerator equipment

    DESCRIPTION
    Programmable device for regeneration of digital channels modulated in DVB-T for BIII and UHF bands. The device regenerates DVB-T digital channels, reconstructing all channels across the VHF-UHF band and obtaining optimal signal quality.

    This modular system consists of a feeder, an amplifier and up to 10 transmodulators that are mounted on a support frame. All functions are programmable via PC software and/or a wireless programmer.

    APPLICATIONS
    MATV installations of digital terrestrial TV and signal transmission or re-transmission installations, where a complete DVB-T channel needs to be regenerated. Areas where the reception of digital channels is difficult due to orographic conditions, or where you wish to improve the quality of the channel considerably. Compatible with all MATV TV installations because the channels are distributed across the entire terrestrial band, BI, BIII, BS and UHF.

    CHARACTERISTICS
    The main characteristic of this device is the high quality of the regenerated output channel and its simplicity of use. Adjustable frequency for input channels in 250 KHz steps. The high selectivity prevents interference between channels and allows frequency conversion without incompatibilities. Chassis in zamak with metallic side covers.
    Female connectors. Simple, fast device assembly.

    Find out more under the Multimedia-TV Products section.

     

    905-ZP: amplification equipment

    DESCRIPTION
    Modular amplification device for analogue and digital terrestrial TV, and for analogue FM and digital DAB radio. It consists of a feeder and amplification modules that are mounted on a support frame.
    It enables the processing of any combination of channels, including adjacent channels with single-channel or multi-channel processing. Simple assembly, easily adaptable to each situation thanks to the input demixing and output mixing system.

    APPLICATIONS
    Medium-to-large MATV digital and analogue terrestrial TV installations. Areas where reception is difficult, with large differences in level between channels.
    Recommended device for installations in residential buildings with a large number of channels.

    CHARACTERISTICS
    The device is characterised by its low consumption, making it highly reliable. Zamak chassis with metal caps. High-quality machined female connectors. Power connection via ribbon cable with 10-pin polarised connectors. Simple, fast device assembly. The main advantage of this device is the quick equalisation and adjustment of all installation channels under any reception conditions, however adverse. Device compatible with the old 905-ZP series.

    Find out more under the Multimedia-TV Products section.

     

    INSTALLATION EXAMPLES:

    DEVICE WITH PROGRAMMABLE AMPLIFIERS

    Complete 905-ZA device where the assembly and module operation methods are indicated. Each ZA-411 module can be programmed for single-channel or multi-channel operation, amplifying several channels, the ZA-431 can be programmed to act as high-selectivity filters for adjacent UHF channels. The ZA-331 can be programmed to act as high-selectivity filters for adjacent VHF channels.

    DEVICE WITH PROGRAMMABLE SINGLE-CHANNEL AMPLIFIERS

    Complete 905-ZG or 905-ZP device where the module assembly methods are indicated. It is recommended to connect the modules with the mixing and demixing bridges as indicated in the drawing. When using the demixing bridges (on top of the device), it is necessary to replace the metal caps for 75ohm loads.

    DEVICE WITH PROGRAMMABLE SINGLE-CHANNEL AMPLIFIERS

    Complete 905-ZG or 905-ZP device where the module assembly methods are indicated. It is recommended to connect the modules with the mixing and demixing bridges as indicated in the drawing. When using the demixing bridges (on top of the device), it is necessary to replace the metal caps for 75ohm loads.

    Find out more under the Multimedia-TV Products section.

    Modulator devices that generate TV channels and complete MATV TV installations in large buildings and hotels with video surveillance cameras and video or DVD machines.

    912-DM: Digital modulator equipment 

    DESCRIPTION
    Modular TV modulator device, which generates a digital TV channel in DVB-T or DVB-C from two audio and video signals. It is a modular system that consists of a feeder, an amplifier and modulators, which are mounted on a support frame. All functions are programmable via PC software and/or a wireless programmer. Multi-standard device.

    APPLICATIONS
    MATV terrestrial or digital cable TV installations where it is necessary to incorporate channels generated locally from SAT receivers, DVDs, videos or surveillance cameras.

    CHARACTERISTICS
    The main characteristic of this device is the high quality of the regenerated output channel and its simplicity of use. Chassis in zamak with metallic side covers. Female connectors. Simple, fast device assembly.

    Find out more under the Multimedia-TV Products section.

     

    912-TT/TQ/TP: Digital satellite equipment

    DESCRIPTION
    Modular transmodulator devices that, based on satellite digital television signals, generate a terrestrial (TT models) or cable (TQ models) or PAL (TP models) digital TV channel. The device converts digital satellite television services into DVB-S / S2 for programmes included in a digital terrestrial TV channel with DVB-T (TT models) modulation, or in DVB-C (TQ models), or PAL (TP models).

    It consists of a feeder, an amplifier and up to 8 transmodulators, depending on the model. All functions are programmable via PC software and/or a wireless programmer. 

    APPLICATIONS
    MATV digital terrestrial television installations where it is necessary to generate a complete DVB-T or DVB-C channel containing services from digital satellite signals with DVB-S/S2 modulation, both free and encrypted. It is not necessary to install individual satellite receivers. Compatible with all MATV TV installations since the channels can be distributed over the entire terrestrial (TT models) or MATV band by cable, since the channels can be distributed throughout the 47-862 MHz band. Compatible with remote control systems.

    CHARACTERISTICS
    Allows the insertion of NIT tables. Programming of the output channel by frequency or by means of a channel table, generating a channel of particularly good quality. Chassis in zamak with metallic side covers. Female connectors. Simple, fast device assembly.

    Find out more under the Multimedia-TV Products section.

    Also known as streamers, these are modular products mounted on a 19” rack, accepting signals from DVB-T / T2, DVB-S / S2, A / V, and HDMI.

    Find more information in the MM-TV Products section.

  • SIGNAL DISTRIBUTION

    SIGNAL DISTRIBUTION

Key advantages

Products of 1st class European Quality

Wide and professional range of products

35+ years facilitating your entertainment

Without expensive maintenance and external installations

Are you interested in our products and solutions?

Info request

close
close overlay